Description
MPN: MODEM-RFD868x-EU
Manufacturer: RFDesign
Product Description:
Please note: The EU certified modems have limited operation modes, a low power (5mW) full duty cycle mode, and a high power (500mW) low duty cycle mode. The low power mode will significantly reduce the effective range of the system and the low duty cycle mode will significantly reduce data throughput. These conditions are a requirement of the certified modems and CANNOT be altered.
RFD868x-EU New Features:
- New Processor, ARM 32-bit core.
- Air data rate: 200kbit/s.
- AES Hardware accelerated encryption. *Fully working*
- RC PPM Passthrough with telemetry at the same time.
- Fully ESD protected + filtered - Every IO port is protected and filtered.
- Original SiK point to point firmware implemented.
- Note: Currently due to the bandwidth limitations of the 868 modems Asynchronous Mesh and Multipoint Firmware are not officially supported for the 868X modems and correct operation of this code cannot be guaranteed
Features:
- Long range >20km depending on antennas and GCS.
- 2 x RP-SMA RF connectors, diversity switched.
- 500mW (+27dBM) See specifications.
- Transmit low pass filter.
- > 20dB Low noise amplifier, high IP3.
- RX SAW filter.
- All I/O ESD protected and filtered.
- Re implemented SiK and firmware, field upgrade-able, easy to configure.
- Small, lightweight.
- Note: Not compatible with older modems
- The standard RFD868x will not communicate with the RFD868x-EU modem unless the standard RFD868x is configured to the same frequency as the EU modem.
Interfaces:
- RF: 2 x RP-SMA connectors
- Serial: Logic level TTL (+3.3v)
- Power: +5v, ~800mA max peak (at maximum transmit power)
- GPIO: 6 General purpose IO (Digital capable).
Specifications:
- Frequency Range: 868-869 MHz
- Output Power: 500mW (+27dBm), controllable in 1dB steps (+/- 1dB @=20dBm typical)
- Air Data transfer rates: 12, 56, 100, 200 kbit/sec (User settable, 200 kbit default) *
- UART data transfer rates: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 1M baud (User settable, 57600 default) *note these values are correct as of version 3.07 SiK firmware.
- Output Power: 500mW (+27dBm)
- Receive Sensitivity: >111 dBm at 12 kbps, 105 at 64 kbps and 98 at 200 kbps.
- Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) - Including RF Shield, Heatsink and connector extremities
- Weight: 14.5g
- Mounting: 3 x M2.5 screws, 3 x header pin solder points
- Power Supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~800 mA peak at maximum power
- Temp. Range: -40 to +85 deg C, tested operational from -73 to +123 deg C.
Software / GCS Support:
The software solution is an open-source development called "SiK". It has been re implemented to suit the new processor architecture available on the 32bit ARM processor core. A boot loader and interface is available for further development and field upgrade of the modem firmware via the serial port.
Most parameters are configurable via AT commands, Eg. baud rate (air/uart), frequency band, power levels.
Integrated support for configuring the RFD radios is supported by APM Planner.
The default settings are at 57600 baud, N, 8, 1, and 200k air data rate.
The RFD868/900x manual is here: RFD900x Manual
The RFD868/900x SiK software manual is here : RFD900x Peer-to-peer Manual
Software features include:
- Frequency hopping spread spectrum (FHSS)
- Transparent serial link
- Point to Point
- Configuration by simple AT commands for local radio, RT commands for remote radio
- User configurable serial data rates and air datarates
- Error correction routines, Mavlink protocol framing (user selectable)
- Mavlink radio status reporting (Local RSSI, Remote RSSI, Local Noise, Remote Noise)
- Automatic antenna diversity switching on a packet basis in realtime
- Automatic duty cycle throttling based on radio temperature to avoid overheating.
Compliance:
We declare that the equipment is in conformity with the relevant Union harmonisation legislation:
Directive 2014/53/EU on radio equipment
The RFD868x-EU is compliant with the following standards:
- EN300 220 V3.1.1
- EN301 489-3 V2.1.1
- IEC 62368-1:2014